Specialist Devices

Hochiki Analogue Plant Control Module with SCI

The CHQ-PCM(SCI) is a loop powered input/output module with four independent change-over relay outputs and four monitored inputs. The outputs feature N/O and N/C volt free contacts and can be driven separately under the control of the fire alarm panel, to be used for the control of devices such as dampers or for plant and equipment shutdown. The four inputs are provided for local fire and fault monitoring and these are fully monitored for open and short circuit, which if required, can be enabled or disabled in pairs using a two-way DIL switch.

The unit is also available in a DIN Rail mountable enclosure – CHQ-PCM/DIN(SCI). A back box is also available (CHQ-BACKBOX) which, when used in conjunction with the CHQ-PCM(SCI), increases the IP rating to IP65. When using heavy cables we recommend the use of the SMB-1 Module Enclosure in conjunction with the SMB-ADAPTOR plate.

Key Features:

Single loop address
Loop powered
4 change-over relay outputs
4 independent inputs for monitoring of volt-free contacts
Each input can be configured to monitor either Normally Open or Normally Closed contacts
DIN rail version available
Both models feature an integral short-circuit isolator
Approved by LPCB

Hochiki Wall Sounder – Red Case

Model CHQ-WS2 is an addressable loop powered Wall Sounder innovatively designed to provide a range of tones and volumes with a maximum output of up to 102dB(A) (±2dB(A)) with low current consumption. The unit is designed to fit to the Standard Base (YBO-R/3(RED)) or the Isolator Base (YBO-R/SCI(RED)).

Hochiki Base Mounting Adaptor White

The YBD-RA(WHT) Surface Wiring Adaptor allows the majority of Hochiki Sensors/Detectors and their Mounting Bases to be fitted flush against a fixing surface whilst also allowing surface wiring (without conduit) to be connected.

The adaptor features four 9mm x 8mm knock-outs for cables/wires allowing surface-fixed wiring to be connected to an appropriate mounting base (depending on application). The adaptor is moulded in ivory white ABS as standard, which allows seamless integration with the majority of mounting bases and associated sensors and detectors.

Key Features:

Compatible with the majority of existing Analogue and Conventional bases
Colour matches standard Hochiki Analogue and Conventional sensor/detector/base ranges
4 pre-moulded knock-outs provide wiring entry
Low profile – only 16mm

Hochiki Base Sounder – Ivory Case

Model YBO-BS is an addressable loop powered Base Sounder innovatively designed to give a range of tones and volumes with a maximum output of up to 98 dB(A) (±2 dB(A)) with low current consumption.

Hochiki Base Sounder – White Case

Model YBO-BS(WHT) is an addressable loop powered Base Sounder innovatively designed to give a range of tones and volumes with a maximum output of up to 98 dB(A) (±2 dB(A)) with low current consumption.

Hochiki Base Sounder Beacon – Ivory case, white LEDs

Hochiki Base Sounder Beacon (Black Case, White LEDs)

Model YBO-BSB2 is an addressable loop powered Base Sounder with integral Beacon, innovatively designed to give a range of tones and volumes with a maximum output of up to 98 dB(A) (±2 dB(A)) with low current consumption. The unit is designed to fit to the Standard Base (YBN-R/3) or the Isolator Base YBN-R/3(SCI) and can be fitted with any of the ESP Range of Sensors, Beacons or Remote Indicators. The unit can also be converted into a wall sounder beacon with the simple addition of a Cap (SI/CAP2). The sounder is Ingress Protection rated to IP21 and for internal use only.

An Auto-Shutdown feature allows the user to set a fixed time within which the sounder or beacon will operate, before automatically shutting down, cutting noise pollution in the case of the sounder element. Sounder and Beacon elements can be operated independently from each other.

Hochiki Base Sounder Beacon – Ivory Case, Red LEDs

Hochiki Base Sounder Beacon (White case, White LEDs)

Model YBO-BSB2(WHT)/WL is an O Rated EN54-23 compliant addressable loop powered Base Sounder with integral Beacon, innovatively designed to give a range of tones and volumes with a maximum output of up to 98 dB(A) (±2 dB(A)) with low current consumption. The unit is designed to fit to the Standard Base (YBN-R/3) or the Isolator Bases (YBO-R/SCI or YBN-R/3(SCI)) and can be fitted with any of the ESP Range of Sensors, Beacons or Remote Indicators.

The unit can also be converted into a wall sounder beacon with the simple addition of a Cap (SI/CAP2(WHT)). The sounder is Ingress Protection rated to IP21 and for internal use only. An Auto-Shutdown feature allows the user to set a fixed time within which the sounder or beacon will operate, before automatically shutting down, cutting noise pollution in the case of the sounder element.

Sounder and Beacon elements can be operated independently from each other
Dependent on control panel compatibility.

Key Features:

Single Loop Address – addressed via the
TCH-B100 Hand Held Programmer
Variable Sound Output 50 ~ 98 dB(A) (±2 dB(A)) output at 1 metre
Sounder and Beacon can operate independently*1
0.5 or 1Hz flash frequency*1
Fits Hochiki Standard or Isolator Base and supports ESP Sensors, Addressable Beacons and Addressable Remote Indicator
51 User-Selectable Tones (all tones EN54-3 compatible)
Auto-Shutdown feature prevents noise-pollution*1
‘O’ Rated Beacon to EN54-23
Available with Red or White LEDs
Available with White or Ivory case
SIL Level 2 approved variant available

Hochiki Base Sounder/Isolator Cover (White)

A protective cap which has been designed for the YBO-BSB2, but can also be fitted to the previous model (YBO-BSB) and the Base Sounder (YBO-BS) when either of these devices isn’t fitted with a sensor. The cap is secured via a twist fit.

The cap can also be added to the isolator base, YBN-R/3(SCI) to create a standalone isolator.

Key Features:

Protects wiring terminals on isolator bases and base sounders/beacons
Easy twist-fit

Hochiki Call Point Key – HCP (10pcs)

Call Point Key – HCP (10pcs)

Hochiki CHQ Box Sub Assembly

The CHQ-SUB Assembly is a set of replacement components designed to fit any of the existing CHQ Modules: CHQ-DIM(SCI), CHQ-SZM(SCI), CHQ-DZM(SCI), CHQ-DSC(SCI), CHQ-MRC(SCI), CHQ-DRC(SCI), CHQ-ISM and CHQ-PCM.

The sub-assembly consists of the PCB tray, PCB cover and semi-opaque lid and can be used in cases where existing module housing becomes damaged and needs replacement.

Key Features:

Robust design
Compatible with all CHQ Modules
Used to replace damaged components

Hochiki Conventional Beacon – Red case, red LEDs (IP65)

CWST-RR-W5 features high output LEDs, advanced optics and an innovative lens design, providing outstanding Omni-directional light coverage at low current draw. Specifically designed for, and approved to meet EN54-23, the CWST-RR-W5 delivers outstanding quality, reliability and long operational life. Weatherproof base provides IP65 for external use applications.

Hochiki Conventional Beacon – Red case, white LEDs

CWST-RW-S5 features high output LEDs, advanced optics and an innovative lens design, providing outstanding Omni-directional light coverage at low current draw. Specifically designed for, and approved to meet EN54-23. The CWST-RW-S5 delivers outstanding quality, reliability and long operational life.

Hochiki Conventional Beacon – Red case, white LEDs (IP65)

CWST-RW-W5 features high output LEDs, advanced optics and an innovative lens design, providing outstanding Omni-directional light coverage at low current draw. Specifically designed for, and approved to meet EN54-23. The CWST-RW-W5 delivers outstanding quality, reliability and long operational life. Weatherproof base provides IP65 for external use applications.

Hochiki Conventional Beacon – White case, red LEDs

CWST-WR-S5 features high output LEDs, advanced optics and an innovative lens design, providing outstanding Omni-directional light coverage at low current draw. Specifically designed for, and approved to meet EN54-23. The CWST-WR-S5 delivers quality, reliability and long operational life.

+44 (0) 203 141 0999

+44 (0) 203 141 0999

Specialist Devices

Hochiki Analogue Plant Control Module with SCI

Hochiki Wall Sounder – Red Case

Hochiki Base Mounting Adaptor White

Hochiki Base Sounder – Ivory Case

Hochiki Base Sounder – White Case

Hochiki Base Sounder Beacon – Ivory case, white LEDs

Hochiki Base Sounder Beacon (Black Case, White LEDs)

Hochiki Base Sounder Beacon – Ivory Case, Red LEDs

Hochiki Base Sounder Beacon (White case, White LEDs)

Hochiki Base Sounder/Isolator Cover (White)

Hochiki Call Point Key – HCP (10pcs)

Hochiki CHQ Box Sub Assembly

Hochiki Conventional Beacon – Red case, red LEDs (IP65)

Hochiki Conventional Beacon – Red case, white LEDs

Hochiki Conventional Beacon – Red case, white LEDs (IP65)

Hochiki Conventional Beacon – White case, red LEDs

+44 (0) 203 141 0999