Speak to our experts

Speak to our experts

+44 (0) 203 141 0999

Odyssey Conventional Devices

smoke detector

Odyssey Conventional Optical Smoke Detector

The Odyssey Conventional Optical Smoke Detector incorporates a pulsing LED located within the housing of the detector. The external detector moulding is identical to that of the ionisation detector but has an indicator LED which is clear in quiescent state but produces a red light in alarm.

  • Responds well to slow-burning, smouldering fires
  • Well suited for bedrooms and escape routes
  • Unaffected by wind or atmospheric pressure
  • Flashing LED and magnet operated test switch option
200-400

Odyssey A1R Heat Detector

The Odyssey Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 4 heat detectors in the Odyssey Conventional designed to suit a wide variety of operating conditions.

  • Can be used for applications where smoke detectors are unsuitable
  • Ideal for environments that are dirty or smokey under natural conditions
  • Wide operating voltage
  • Flashing LED and magnet operated test switch option
200-403

Odyssey CS Heat Detector

The Odyssey Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 4 heat detectors in the Odyssey Conventional designed to suit a wide variety of operating conditions.

  • Can be used for applications where smoke detectors are unsuitable
  • Ideal for environments that are dirty or smoky under natural conditions
  • Wide operating voltage
  • Flashing LED and magnet operated test switch option
200-401

Odyssey BR Heat Detector

The Odyssey Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 4 heat detectors in the Odyssey Conventional designed to suit a wide variety of operating conditions.

  • Can be used for applications where smoke detectors are unsuitable
  • Ideal for environments that are dirty or smoky under natural conditions
  • Wide operating voltage
  • Flashing LED and magnet operated test switch option
200-402

Odyssey CR Heat Detector

The Odyssey Heat Detector monitors temperature by using a dual thermistor network which provides a voltage output proportional to the external air temperature. There are 4 heat detectors in the Odyssey Conventional designed to suit a wide variety of operating conditions.

  • Can be used for applications where smoke detectors are unsuitable
  • Ideal for environments that are dirty or smoky under natural conditions
  • Wide operating voltage
  • Flashing LED and magnet operated test switch option
Odyssey Standard Base

Odyssey Standard Base

The Odyssey Standard Base has been designed to enable detectors to be fitted without the need of force – particularly useful when fitting to suspended ceilings. All Odyssey bases have a ‘one way only’ fit. Detectors can be locked into place by a grub screw using a 1.5mm hexagonal screwdriver.

  • Detector locking mechanism
  • One way fit
  • Easy to wire
  • Contains an earth connector
  • Contains no electrical parts
  • Terminal for remote indicator
odyssey-diode-base

Odyssey Diode Base

The Odyssey Diode Base is designed for use with conventional systems that have manual call points and detector bases on the same circuit. The base is fitted with a schottky diode on the “L1 IN” and “L1 OUT” wiring terminals. This base can only be used with compatible control equipment.

  • Detector locking mechanism
  • One way fit
  • Easy to wire
  • Contains an earth connector
  • Continues to work during unauthorised removal of detectors
odyssey-sav-wire-base

Odyssey Sav-Wire Base

The Odyssey Sav-Wire Base is designed to allow Odyssey conventional detectors to be used in ‘Sav-Wire’ detection and alarm systems.

  • Detector locking mechanism
  • One way fit
  • Easy to wire
  • Contains an earth connector
Odyssey Relay Base

Odyssey Relay Base

The Odyssey Standard Relay Base provides one set of volt-free changeover (form C) contacts that change state when the detector signals an alarm.

  • Detector locking mechanism
  • One way fit
  • Easy to wire
  • Contains an earth connector
odyssey-12v-relay-base

Odyssey 12V Relay Base

The Odyssey Conventional 12V Relay Base is designed for use in both fire and security systems. For fire systems a jumper on the PCB is fitted to a ‘latching’ position. For security systems the jumper is moved to another position so that the base is ‘non-latching’.

  • Detector locking mechanism
  • One way fit
  • Easy to wire
  • Contains an earth connector
  • Can be used in fire and security systems
fire call point

SyCall Conventional Manual Call point

SyCall is a resettable manual call point packed with unique and innovative features. It has been designed to obtain maximum visibility, high reliability in operation and pleasant aesthetical appearance and is fully approved to EN54-11.

Six modes of operation are achievable simply by choosing the appropriate internal connection terminals at the time of installation. This solution has been adopted to address the need to stock multiple units commonly seen in many other popular types of call points on the market.

The unit is highly visible in both the alarm and non-alarm state. Front facing LED and sideways facing light tubes allow the easy discovery of an activated call point.

Features

  • Red surface mount version only is approved to EN54-11
  • Very high visibility of the alarm condition
  • Visible in the dark via the unique luminescent resettable element feature
  • Easy and economical installation
  • High impact resistant ABS plastic materialalso available in blue, green and yellow
  • Clever six configurations in one unit design for reduced inventory holding
  • Surface mount and flush mount options available
  • Extremely easy to reset via the robust twist and set key
    system
fire call beacon

SyCall Conventional 2 Wire Manual Call point

SyCall is a resettable manual call point packed with unique and innovative features. It has been designed to obtain maximum visibility, high reliability in operation and pleasant aesthetical appearance and is fully approved to EN54-11.

The SyCall manual call point also comes in a 2 wire (Sav-Wire) variant.

Six modes of operation are achievable simply by choosing the appropriate internal connection terminals at the time of installation. This solution has been adopted to address the need to stock multiple units commonly seen in many other popular types of call points on the market.

The unit is highly visible in both the alarm and non-alarm state. Front facing LED and sideways facing light tubes allow the easy discovery of an activated call point.

Features

  • Red surface mount version only is approved to EN54-11
  • Very high visibility of the alarm condition
  • Visible in the dark via the unique luminescent resettable element feature
  • Easy and economical installation
  • High impact resistant ABS plastic materialalso available in blue, green and yellow
  • Clever six configurations in one unit design for reduced inventory holding
  • Surface mount and flush mount options available
  • Extremely easy to reset via the robust twist and set key
    system
EVTB Red Sounder Beacon Red Lens Deep Base

EVTB Conventional Wall Sounder Beacon

The EVTB 24Vdc sounder beacon is part of the EVTG family of products designed for use with conventional fire alarm
systems including two wire (SAV-WIRE®) and other general 24Vdc applications. The sounder function, like all EVTG products, comes as standard with 32 tones. The beacon function has been designed for maximum all-round visibility, coupled with low power consumption utilising an array of energy efficient LEDs. The sounder function features a two-stage alarm override which is activated by a third negative wire from the fire panel. Both the sounder and beacon functions are fully synchronised. The product can also be used as a beacon only which is easily selected by a DIL switch at the time of installation.

Features

  • 32 tones plus a selectable override tone
  • Shallow base IP43 and deep base IP65 versions available
  • Switch selectable beacon only feature
  • Unique twist and lock bayonet mounting system
  • Removable cover on deep base for surface wiring
  • Features base locking system as standard
EVTG Sounder Red Shallow Base

EVTG Conventional Wall Sounder

The EVTG family of sounders has been designed to cover a wide spectrum of applications. The 24 volt EN54-3 approved version is for use with conventional fire alarm systems including two wire (SAV-WIRE®) and as standard comes with 32 tones. The sounder is supplied with a two stage alarm override which is activated by a third negative wire from the fire panel.

All tones have been selected to comply with the latest sound patterns and frequencies used throughout the world. All tone options are fully synchronised. The sounder function has been fully approved to EN54-3 by the LPCB and VdS on tones 1, 8, 11, 25 and 27.

Features

  • Fully approved to EN54-3 by LPCB and VdS
  • 32 tones plus a selectable override tone
  • Shallow base IP21C and deep base IP33C versions available
  • Designed to work with both conventional and two-wire (SAV-WIRE®) systems
  • Unique twist and lock bayonet mounting system
  • Removable cover on deep base for surface wiring
  • Features base locking system as standard
VBL-6

VBL-6 24v 6” Low Current Bell

The VBL 6″ motorised bell has been designed to offer maximum performance combined with rapic installation and a sleed low profile appearance. The bell is used for a wide range of alerts including fire alarm. The unit comes complete with a tamper resistant hex bolt and for easy installation an allen key is provided.

  • Low current consumption
  • Available in red of grey
  • Low profile design
EVSO Base Sounder

EVSO-32-W 24V 32 Tone White Platform Sounder EN54 Approved

The EVSO base sounder is for use with conventional fire alarm systems, including two wire (SAV-WIRE®) and is designed to accept most leading detector bases and offers a cost-effective solution to sounder installation. The low profile sounder is supplied with 32 tones, along with a two stage alarm override which is activated by a third negative wire from the fire panel.

All tones have been selected to comply with the latest sound patterns and frequencies used throughout the world. All tone options are fully synchronised. This sounder has been fully approved to EN54-3 by the LPCB and VdS on tones 1, 3, 11, 25 and 27.

When a detector is not fitted to the sounder, a blank cover plate is available so that the unit can be used as a standalone sounder.

Need to talk to a member of the team?

Our support & sales team are keen and would love to help with any questions. Leave your details in the contact form and we will get back to you shortly.